Posts Tagged ‘Liberty Ship’

A heavy tale of Kaiser ships, graveyards, and uncles

posted on November 19, 2014

Lincoln Cushing
Heritage writer

 

scrapped Liberty ship bow, Willamette River

Scrapped Liberty ship fore peak, Willamette River, Oregon. [1]

Buried on the banks of the Willamette River in Portland, Oregon, lies an unmarked graveyard of war veterans. And my uncle played a small but important role in their short lives.

At the end of World War II, a parade of proud but battered ships arrived at U.S. scrapyards to be recycled. Many of these were Kaiser-built Liberty and Victory ships completing their destiny after having helped win the war for the Allies. Like spawning salmon, many of these ships were returning to be recycled only miles from the three Portland and Vancouver (Wash.) yards in which they were built. But when workers took cutting torches to these noble vessels, they ran into a problem – solid ballast.

Every ship requires ballast to stay upright, and cargo ships have particularly challenging demands. If ballast is not properly placed fore to aft or side to side, or there’s not enough of it, a ship will not be trimmed properly and risk listing or even capsizing under adverse conditions. In extreme circumstances uneven ballast and cargo loading can break a ship in high seas. And since these vessels are constantly taking on and removing massive quantities of cargo, ballasting is a dynamic problem.

As is typical in large vessels, Liberty ships were built with multiple ballast holds. These included “deep tanks” below the main cargo holds that could contain dry cargo or sea water ballast; even deeper “double bottom” tanks that could carry either fuel oil or seawater ballast; and designated holds for permanent solid ballast.

Liberty ship holdsV3-sm

Diagram of Liberty ship holds, fore peak highlighted. [2]

Solid ballast can be anything from rocks to iron, and has the advantage of being much denser (and thus heavier) than water. Liberty ships were built with a dead weight capacity of 10,800 tons and required 1,500 tons of ballast. The engine was in the center, but to compensate for the aft weight of the rudder, screw, and prop shaft the ship’s lower bow section – the fore peak – was filled with solid ballast. They also produced “movable ballast” cast blocks, usually 9x11x13 inches and weighing about 175 pounds, which could be moved or removed as needs changed. At first pig iron was used, but even that lowly metal was too precious to waste on ballast during the war. Alternatives were sought, and eventually found – in the form of magnetite-infused concrete.

Magnetite is low-grade iron ore, generally unsuitable for manufacturing, with a specific gravity of 5.17. That is less dense than pig iron’s 7.1 but far higher than concrete’s 2.32. The magnetite-concrete mixture was considerably cheaper than metal; a 1948 U.S. Department of the Interior report noted that the substitution saved about $2 million during war production.

Although most of the magnetite used on the Pacific Coast came from California. a major deposit was available from a Lovelock (Nevada) mine controlled by Charles H. Segerstrom, Jr. and John M. Heizer. John was my uncle; my other uncle Robert was working as a steamfitter in the Kaiser Richmond shipyards at the time. As early as October, 1943 rail cars were carrying one carload a day from the mines to ballast fabricators near San Francisco bay. 

This is how it was reported in “Nevada iron deposits provide warship ballast,” published in the Mineral County (Nevada) Independent News, June 13, 1945:

The ore is high-grade magnetite (60 to 65 percent iron) of high specific gravity and is in demand by west coast shipbuilders. Crushed magnetite and Portland cement are mixed with magnetite sands recovered magnetically from beaches in California, and the mixture is placed as concrete in the ship bottoms to set as a permanent ballast…

Heizer and Segerstrom have subleased the property to the Dodge Construction company of Fallon to fulfill a contract in excess of 10,000 tons of magnetite iron ore to be used by Kaiser shipyards of Richmond, California. Production of the magnetite started in early July, 1944.

Magnetite iron ore has been used successfully for permanent ship ballast and the Kaiser shipyards have contracted for an additional tonnage. Meanwhile, the shipyards at Portland, Oregon, have also negotiated for a substantial tonnage.

 

Bows on riverside-sm

Scrapped fore peaks, Willamette River [3]

The ballast was a great solution for shipbuilding, but later on it posed a problem for postwar shipbreaking. The concrete could not be easily separated from the valuable steel, so the fore peaks were deposited at the edge of the river as erosion-control landfill.

Portland shipbreakers at yards such as Zidell tackled more than 183 Liberty ships, buttressing the Willamette River shore with more than 100 fore peaks and other ballast blocks. In 1991, the Naito family created the Portland Liberty Ship Memorial Park, setting it on property they had purchased. In 2006 this park was redeveloped into a high-end condo community, literally built on top of the bows of a marvelous wartime achievement.

Plans are being made to honor this past with an outdoor maritime display on the Willamette River Greenway. Perhaps these battered remnants of the World War II Home Front merchant marine fleet will once again raise their peaks and proclaim “We can do it!”

 

Short link to this article: http://bit.ly/14NMsym

[1] Photo from “Portland South Waterfront Greenway: Conceptual Schematic Design Phase,” August, 2004, Buster Simpson; also photo #3.

[2] Liberty ship schematic adapted from Sawyer, L. A., & Mitchell, W. H. (1970). The Liberty ships: The history of the “emergency” type cargo ships constructed in the United States during World War II. Cambridge, Md: Cornell Maritime Press.

 

Tags: , , , , ,

In Memory of Lena Horne & Launch of the SS George Washington Carver Liberty Ship

posted on May 10, 2010

By Tom Debley
Director of Heritage Resources

Singer Lena Horne prepares to launch the SS George Washington Carver on May 7, 1943 at Kaiser Shipyard No. 1 in Richmond, Calif. This was taken by black photographer E. F. Joseph for the Office of War Information.

This week we pay tribute to the great jazz singer Lena Horne, who died Sunday, May 9, at the age of 92.

What’s her connection to Kaiser Permanente? Sixty-seven years ago, on May 7, 1943, Lena Horne broke a bottle of champagne across the bow to launch the SS George Washington Carver, a brand new Liberty ship built in Henry J. Kaiser’s legendary World War II shipyards in Richmond, Calif.

She was proudly representing the more than 7,000 African American shipyard workers — 1,000 of them female “Rosie the Riveters” — and all of whom received their health care from the medical care program that would become Kaiser Permanente after the war.

Their story is part of Kaiser Permanente’s long and proud history of ethnic and cultural diversity.

The SS George Washington Carver was the first Kaiser-built Liberty ship to be named for a famous African American, and many of the men and women who built it were African Americans.

Anna Bland, a burner, is shown at work on the SS George Washington Carver as it was being rushed to completion in the spring of 1943.  Photograph by E. F. Joseph for the Office of War Information.

Carver, you will recall, was the scientist, botanist, educator, and inventor who had died only four months earlier in 1943. Who better to christen her on her maiden voyage than one of America’s most admired  and talented African American women?

Also on hand that day was a well-known African American photographer, E. F. Joseph, who recorded the event for the Office of War Information.

The ship was initially assigned by the War Shipping Administration (WSA) to the American South African Line, Inc. for merchant service. But in November 1943 the ship was turned over to the United States Army and converted to the Hospital Ship Dogwood.

In January 1946, the ship was again converted to carry a combination of troops and military dependents as the USAT George Washington Carver before retiring to National Defense Reserve Fleet.  It was sold for scrap in 1964.

Today, the story of these African American workers, the SS George Washington Carver, and its launch by Lena Horne is one of the legacy stories of the Home Front that is part of the history that is shared in the Rosie the Riveter / World War II Home Front National Historical Park in Richmond, Calif.

Tags: , , , , , ,